Ben Nye's Nose & Scar Wax alters the appearance of real skin to imitate all sorts of distortions! Fake a broken nose, extended nose or chin, bullet holes and wounds with this pliable yet firm wax. Translucent to resemble skin. Apply spirit gum beneath wax for better adhesion. Texture with a Fine Stipple Sponge and seal with liquid latex or Sealer. 2
Kryolan F/X Wax
Great for creating bullet wound, with noses, scars etc, F/X wax is used to simulate realistic-looking injuries and alter natural face shapes. It is also used to block out eyebrows. This silicone-containing wax can be removed from the container with a spatula and then applied and shaped on the skin using fingers and the spatula. If the wax becomes too sticky add a very small amount of vaseline to your fingers and continue blending.To set, powder with translucent powder and then thinly coat with sealer. Powder again. Once set, makeup can be applied. easily removed by scraping off with a spatula.
Not tested on animals
Cine-Wax is a special effects product for the creation of small 3D effects, easy to use and blend into the skin. It is recommended that Kryolan Sealer is applied over the Cine-Wax once the desired effect has been achieved, to make it stronger and firmer and thus more likely to last. It is easily removed from the skin by simply scraping off.
Tip: if you find your fingers get a bit sticky whilst molding the wax, apply a little vaseline to your fingers.
Not tested on animals
Kryolan Nose Putty
A wax stick composition for altering the shape of the nose. Fingers should first be moistened with a little water or gel to prevent putty from sticking, then knead in hand until pliable. Can be adhered to the skin with Spirit Gum.
Kryolan Plastici Wax
A tinted soft wax for modelling noses, chins or facial contours on body surfaces. May also be used to block out eyebrows, create scars and change contours. Must be coated with a sealer.
Kryolan Eyebrow Plastic
A flesh-coloured wax stick for blocking out eyebrows. Wax stick may be first applied on brow in stroking motions from nose bridge out to end of brow. Reverse this motion from outer edge of brow to nose bridge and then repeat the first motion. When brow is covered with wax then cover with 1 to 2 coats of sealer. A favourite with our drag clients!
Kryolan Eyebrow Design Kit
The Eyebrow Design Kit contains all necessary products to block away eyebrows. In the first step, eyebrows are flattened using Hydro Gum, followed by the application of F/X Wax and then sealed with the included Sealer. Finally, the area should be made up using either Ultra Foundation, TV Paint Stick, Supracolor, Dermacolor Camouflage or Vitacolor. For best results, the foundation should be set with Translucent Powder. Detailed instructions enclosed.
Kryolan Moustache Wax
Wax used for old-fashioned styling of fake or real moustaches.
Kryolan Hydro Spirit Gum
A water-based adhesive containing no solvent. Water-soluble Spirit Gum is effective in adhering objects for short periods of time, and for holding down hair and eyebrows before they are covered with a bald cap or plastic film. Use a brush to apply and allow to dry slightly before adhering the required hair or objects. Since this is a water-based preparation, it will dry slowly; warm air can be used to speed up the drying process. Easily removed with soap and water.
Sealer is a clear synthetic liquid used for protection over special effects makeup products like latex, foam, wax models, putty noses, chins and other prosthetic pieces. Use a brush to apply thinly over wax models, and for a border of 1 cm beyond the model onto the bordering skin. Allow to dry, and then apply powder. As needed, Kryolan Sealer can be diluted with Kryolan Spirit Gum Remover or alcohol.
Stay in the know to get special offers, free giveaways and once-in-a-lifetime deals.